- Wuhan Guodian Mingke Electric Co., Ltd.
- China Manufacturer with main products:Series resonance test device ,Transformer tester ,Circuit breaker , switch tester ,High Voltage Insulation Equipm ,Relay Protection Products ,Cable and cable fault tester ,Arrester and Insulator Test In ,SF6 Test Instrument ,Oil Testing Instrument ,DC System and Battery Test Ins ,Ground/Insulation Resistance T ,Power Energy Analyzer ,Power Energy Analyzer
Home > Company News > Operation Method Of Transformer Voltage Test Control Box
Company News
Pressure test control box, using advanced microelectronic processing technology, all use process can be set in advance, all Chinese interface, simple operation. After all test items are set, the pressure test control box can be tested automatically without manual intervention.
1. According to the relevant regulations, set up the site, connect the equipment connection, and there should be special personnel in charge of safety in the area where conditions permit.
2. The current relay (KA) should be adjusted according to the capacity and voltage level of the tested object before the operation of the voltage withstand test control box.
3. Turn on the power switch, press the power transmission button, the contactor is closed, the live power signal light of the voltage regulator is off, and the power transmission signal light is on. At this time, the boost test can be carried out.
4. Turn the handle of the voltage regulator slowly clockwise (press the rising button on the electric console) and pay close attention to the voltmeter (it is appropriate to increase the voltage at the speed of 3KV per second). When the voltage is increased to the specified withstand voltage value of the tested object, press the timing button in time and pay close attention to the condition of the tested object.
5. When the specified withstand time of the tested object is reached, an alarm (Bell) will sound in the table (box), indicating that the tested object is qualified for withstand voltage. At this time, turn the handle of the voltage regulator anticlockwise (press the down button on the electric console) to make the voltage regulator return to zero. And press the stop button to cut off the power.
6. In case of over-voltage in the process of voltage rise or voltage withstand test, the voltage regulator knob shall be turned anticlockwise in time (the electric console presses the down button) to make the voltage return to the specified value.
7. During the test, if the current indication of the ammeter exceeds the specified range of the tested object, the boost voltage shall be stopped immediately, and the relevant reasons shall be found out before the test.
8. In case of short circuit, flashover, breakdown and other over-current in the process of voltage rise or voltage withstand test, the current relay will act to make the voltage regulator cut off automatically, indicating that the tested product is unqualified. At this time, return the voltage regulator to zero and reset the timing button for the next operation.
- EI-18 50W Planar Transformer
- EL-18 40A Planar Transformer
- EI-22-1 150W Planar Transformer
- EI-22-2 150W Planar Transformer
- ER23-2 120W Planar Transformer
- EL-25 150W Planar Transformer
- Acrel leakage current transformer rated current 400-800A Applied to residual current signal collection AKH-0.66/L L-150
- Acrel measuring rated current 250-400A low voltage leakeage CT Residual current transformer AKH-0.66/L L-100
- Acrel Applied to residual current signal collection residual current transformer AKH-0.66/L L-200 rated current 800-1500A
- Acrel AKH-0.66/L L-80 rated current 100-250A Applied to residual current signal collection measurement current transformer
- Acrel leakage current transformer rated current 400-800A Applied to residual current signal collection AKH-0.66/L L-150
- Acrelrated current 800-1500A Applied to residual current signal collection residual current transformer AKH-0.66/L L-200
- Acrel AKH-0.66/L L-45 residual current transformer rated current 16-100A Applied to residual current signal collection
- Acrel Can be widely used in industrial automation fields smart AC current transformer BA20(II)-AI/V
- Acrel smart AC electrical transducer BA50(II)-AI/V Mainly detects the leakage current of the electrical system
- Acrel BA50L(II)-AI/V smart AC electrical current sensor Can be widely used in industrial automation fields out 1-5V/0-5V
- Acrel BA50L(II)-AI/V Can be widely used in industrial automation fields out 1-5V/0-5V smart AC electrical current sensor
- Made in China Three phase dry type transformer SG-100VA for thermal power plant
Popular Searches
- power transformer
- Distribution Service
- current transformer
- power transformers
- High Frequency Transformer
- Electrical Transformer
- energy saver device
- led transformers
- step up converter
- Ac Drive Converter
- Frequency Drive Converter
- electronic transformer
- Lighting Transformers
- toroidal transformer
- auto transformer
- voltage transformer